|
| Metric Thread Plug & Ring Gauge |
American Standard Thread Plug & Ring Gauge |
Taper Pipe Thread Gages |
| DIN13 ISO1502-96 | |
 |
 |
| COARSE | FINE | |||||
|---|---|---|---|---|---|---|
| Nominal Size | Pitch 1 | Pitch 2 | Pitch 3 | Pitch 4 | Pitch 5 | Pitch 6 |
| M1.0 | 0.25 | 0.20 | ||||
| M1.1 | 0.25 | 0.20 | ||||
| M1.2 | 0.25 | 0.20 | ||||
| M1.4 | 0.30 | 0.20 | ||||
| M1.6 | 0.35 | 0.20 | ||||
| M1.8 | 0.35 | 0.20 | ||||
| M2.0 | 0.40 | 0.25 | ||||
| M2.2 | 0.45 | 0.25 | ||||
| M2.5 | 0.45 | 0.35 | ||||
| M3.0 | 0.50 | 0.35 | ||||
| M3.5 | 0.60 | 0.35 | ||||
| M4.0 | 0.70 | 0.50 | ||||
| M5.0 | 0.80 | 0.50 | ||||
| M6.0 | 1.00 | 0.75 | 0.50 | |||
| M8.0 | 1.25 | 1.00 | 0.75 | 0.50 | ||
| M10.0 | 1.50 | 1.25 | 1.00 | 0.75 | 0.50 | |
| M12.0 | 1.75 | 1.50 | 1.25 | 1.00 | 0.75 | 0.50 |
| M14.0 | 2.00 | 1.50 | 1.25 | 1.00 | 0.75 | 0.50 |
| M16.0 | 2.00 | 1.50 | 1.00 | 0.75 | 0.50 | |
| M18.0 | 2.50 | 2.00 | 1.50 | 1.00 | 0.75 | 0.50 |
| M20.0 | 2.50 | 2.00 | 1.50 | 1.00 | 0.75 | 0.50 |
| M22.0 | 2.50 | 2.00 | 1.50 | 1.00 | 0.75 | 0.50 |
| M24.0 | 3.00 | 2.00 | 1.50 | 1.00 | 0.75 | 0.50 |
| M27.0 | 3.00 | 2.00 | 1.50 | 1.00 | 0.75 | |
| M30.0 | 3.50 | 3.00 | 2.00 | 1.50 | 1.00 | 0.75 |
| M33.0 | 3.50 | 3.00 | 2.00 | 1.50 | 1.00 | 0.75 |
| M36.0 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 | |
| M39.0 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 | 1.00 |
| M42.0 | 4.50 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 |
| M45.0 | 4.50 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 |
| M48.0 | 5.00 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 |
| M52.0 | 5.00 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 |
| M56.0 | 5.50 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 |
| M60.0 | 5.50 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 |
| M64.0 | 6.00 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 |
| M68.0 | 6.00 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 |
| M72.0 | 6.00 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 |
| M76.0 | 6.00 | 4.00 | 3.00 | 2.00 | 1.50 | 1.00 |
| M80.0 | 6.00 | 4.00 | 3.00 | 2.00 | 1.50 | |
| M85.0 | 6.00 | 4.00 | 3.00 | 2.00 | 1.50 | |
| *** | *** | *** | *** | *** | *** | |
| M320 | ||||||
| * Other sizes and tolerances on request |